To the best of our knowledge all details listed below are deemed correct.
          It is the buyers responsibility to confirm ALL details prior to purchase.
          
          Option: These new machines are being sold as-is with pre-installation checkout
          in Chatsworth, Califonia. Parts Warranty Only Starting at: $10,000.00
          
          Equipped With:
             12,000 RPM Direct-Drive Beltless Spindle
             Big-Plus Dual-Contact High Performance Precision Spindle
             40-Tool High Speed Twin Arm Tool Changer
             32-GB Solid State Data Server Intergral to CNC Control
             Chip Wash Down Coolant System
             Twin Chip Augers to Push Chips Forward
             300 PSI "Through-the-Spindle" Coolant System with Deublin Rotary Union
             Full Machine Enclosure with Top Covers (precut for exhaust duct)
             Spindle Air Blast by M-Code
             Spindle Oil Cooler - Thermostatically controlled
             Remote Operator MPG Hand wheel
             High Speed Synchronous Rigid Tapping
             Dual LED High-Intensity Worklamps
             6-Thru-Tool-Coolant Pull Studs
             4th & 5th Axis Prewired with a Quick-Disconnect Connectors
          
          Axis Travel
             X-Axis (6 Cross Roller Trucks):        63"            1,600mm
             Y-Axis (4 Cross Roller w/ 8 Trucks:    33.4"          850mm
             Z-Axis:                                33.4"          850mm
             Spindle to Rotary Table Surface:       5.9-39.37"     150-1000mm
             Spindle Center to Z Way Covers:        33.4"          850mm (Troat)
          
          Table
             Table Size:                            68.8" x 27.56" 1,750mmx700mm
             T-Slot Width (3 T-Slots Total):        18mm           100mm Centers
             Table Load:                            5500 lbs       2500 kgs load
          
          Spindle
             Spindle Motor:                         40 HP S3 Power 35HP 30-Min
          
             Spindle Speed:                         12,000 RPM
          
             Spindle Torque:                        90 ft-lb @ 1,500 RPM
             Tool Type:                             CAT #40 Taper
          
             Retention System/Holding Capability    BellVille Spring Stack (1650-1760 lbs)
             Spindle Runout:                        <0.000040" TIR
             Spindle Bearings - Rear:               110mm NSK70BNR 2-P4 Class 7 Bearing
             Spindle Bearings - Front:              110mm NSK70BNR 2-P4 Class 7 Bearing
             Retention Knob:                        C40-4502H (Coolant)
          
          Axis Feeds
             Rapid Traverse (X,Y):                  984 IPM        25m/minute
             Rapid Traverse (Z):                    984 IPM        25m/minute
             Cutting Feedrate:                      0.4-393 IPM
          
             Ballscrews (X,Y,Z):                    50mm Ballscrews10mm Pitch
             Least Input Command Increment:         0.0001"/0.000040"0.001mm(40 Millionth)
             Accuracy X,Y,Z Axis (JIS6338):         +0.0002"/12"   +0.005mm Over 300mm
             Repeatability X,Y,Z Axis (JIS6338):    +0.0001"/12"   +0.003mm Over 300mm
          
          Tool Changer
             Tool Capacity (40+1):                  40 Tool Twin Arm
             Tool Shank:                            CAT#40 Taper
          
             Tool Change Time:                      3.7 Seconds Tool to Tool
             Tool Diameter / w/adjacent tool:       5.90" / 3.15"  150mm/80mm
             Tool Length/Weight (from gage line):   11.81" / 15 lbs300mm/7Kg
             Tool Selection/Tool Access             Random         Bi Direction: 
          
          General
             Coolant Capacity:                      148-Gallons    560 Liters
             Electrical - Connected Load:           75 amps        220vac+5%, 60hz
             Air Service Requirements:              85 PSI @ 14-scfm
             Machine Dimensions:                    185" x 130" x 120"470x330x260cm
             Machine Weight:                        26,455 lbs     12,000 kg
          
          
          *Machine Options*
          
          Factory machine installation: "Peace-of-Mind Factory Installation" - Includes
          
          Expenses:                                                POR
          
          
          Factory On-Site 3-Day Machine Operation and Program Training - Includes
          
          Expenses:                                                POR
          
          
          Belt Type Chip Conveyor w/ 38" Barrel Height Discharge:  POR
          
          
          Substitute #40-Taper 8,000 RPM 2-Speed ZF Geared-Head Spindle:
                                                                   POR
          
          
          Substitute #50-Taper 6,000 or 8,000 RPM Geard-Head Spindle:
                                                                   POR
          
          
          Substitute #50-Taper Direct-Drive 10,000 or 12,000 RPM Spindle: 
                                                                   POR
          
          
          Second-Year Machine and Control Warranty:                POR
          
          
          Voltage Stabilizers/Transformers (Specify Voltage):      POR 
          
          1,000 PSI Through-The-Spindle Coolant System-Installed:  POR
          
          
          Heidenhain Linear Scales for All 3-Axis - Installed:     POR
          
          
          
          

Automatics & Machinery Co Inc
150 Martin St Longmont CO 80501-5939
Tel: 800-543-7666 Fax: 303-651-6556
Email (Request Quote): steve@automatics.com
Web: www.automatics.com